Exam Dumps HPE2-T37 Practice Free Latest HP Practice Tests
HPE2-T37 Exam Questions | Real HPE2-T37 Practice Dumps
NEW QUESTION 21
Which statement about an HPE OneView server profile is true?
- A. A server profile created for a specific server hardware type cannot be moved to a server with a different server hardware type.
- B. A server profile can be used to configure a local storage controller, but cannot be used to configure SAN-based storage.
- C. A server profile can be used to update firmware and drivers when the operating system on the server is up and running.
- D. A server profile can be created only for HPE BladeSystem, HPE Synergy, and HPE Superdome Flex servers.
Answer: B
NEW QUESTION 22
Click the option that must be configured for an HPE OneView when an HPE storage system is connected directly to an HPE Synergy frame.
Answer:
Explanation:
NEW QUESTION 23
Your customer built a sever profile for HPE Synergy Gen 10 server and configured boot mode to Legacy BIOS. Which feature Is not available for this Compute Module?
- A. Workload profile
- B. Boot from SAN
- C. Secure boot
- D. BIOS management
Answer: C
NEW QUESTION 24
Refer to the exhibit.
You discovered that one of the profiles is not compliant with the server profile template. What could cause this profile to be inconsistent with the server profile template?
- A. Changes to the server profile were implemented directly on the server profile.
- B. The server was powered off or rebooted recently and IL0 did not reconnect to HPE OneView.
- C. Network connectivity for HPE Synergy Compute Module was changed outside HPE OneView.
- D. HPE OneView was restored from a backup that created ^consistency with the server profile template.
Answer: C
NEW QUESTION 25
You want to put two FlexNlCs into a single Link Aggregation Group within a server profile. What Is a prerequisite for this setup?
- A. The Compute Module profile must have exactly two connections defined.
- B. Both FlexNlCs must be connected to the same network.
- C. An upgrade license must be purchased and deployed.
- D. The sFlow option must be enabled and configured.
Answer: D
NEW QUESTION 26
As a part of troubleshooting, you have to reinstall the same version of the firmware on an HPE Synergy Compute Module. Click the area within the Firmware section of the server profile that will allow you to install the same firmware version.
Answer:
Explanation:
NEW QUESTION 27
A customer has to deploy 21 HPE Synergy Compute Modules in a boot from SAN setup. How this task can be simplified while keeping the profile consistent?
- A. Boot volumes can be prepared in advance and later presented as shared volumes to the Compute Modules.
- B. An existing volume can be replicated automatically when creating a server profile.
- C. Boot volumes can be created on demand and defined in the server profile template.
- D. single SAN volume can be created and utilized by all HPE Synergy Compute Modules.
Answer: C
NEW QUESTION 28
Your customer is considering HPE Synergy as a hardware platform for visualization workload. The customer environment is wry dynamic, and they often have to modify hypervisor networking.
Which resource provided by HPE should you discuss with this customer?
- A. HPE Image Streamer provides templates which can be updated to map the hypervisor requirements
- B. PowerShell Library for HPE OneView allows scripted environment modification.
- C. HPE OneView for VMware vCenter Server will enable host profile functionality and simplify changes.
- D. HPE OneView Global Dashboard allows server profile replication and change management.
Answer: A
NEW QUESTION 29
Refer to the exhibit.
Your customer created multiple networks in HPE OneView, but only Eth-1 is available to be used within a server profile. What is a likely cause of this situation?
- A. The other networks are not added to the Logical Interconnect Group configuration.
- B. The other networks are configured with a purpose other than General or Management.
- C. The other networks have Private Network' selected, which hides them from Compute Modules.
- D. The other networks are not configured with the required Smart Link parameter.
Answer: C
NEW QUESTION 30
Your customer wants to use HPE OneView for VMware vCenter Server to simplify management of their VMware cluster running on HPE Synergy. The customer is concerned with the cost of additional licenses.
How will you explain licensing rules for this product?
- A. As long as the customer has HPE OneVtew Global Dashboard deployed, HPE OneView for VMware vCenter Server does not require any additional licenses.
- B. One HPE OneView for VMware vCenter Server license is required per HPE Synergy frame if more than
10 Compute Modules are installed in the frame. - C. If the number of the HPE Synergy Compute Modules installed in HPE Synergy frame is less than 10, no license is required to use HPE OneView tor VMware vCenter Server.
- D. As long as the server is managed using HPE OneView. the customer can use HPE OneView for VMware vCenter Server without additional licenses.
Answer: B
NEW QUESTION 31
Which statement about a server profile for an Apollo system is true?
- A. Virtual WWNs and MAC addresses can be defined
- B. UEFI optimized is the only available boot mode
- C. Fibre Channel connections can be defined
- D. Enclosure Group Is automatically selected
Answer: A
NEW QUESTION 32
Refer to the exhibit.
After adding SAN Manager to HPE OneView. you noticed that all SANs are in the discovered state. How will this affect HPE OneView storage management capabilities?
- A. Auto-zoning functionality will not work until SANs are associated with networks.
- B. Volume presentation through server profile will work with the discovered state.
- C. Snapshot functionality will be limited only to the volumes not using these SANs.
- D. Volume provisioning will only work for arrays that ate accessible through these SANs.
Answer: B
NEW QUESTION 33
Refer to the exhibit.
Which statement about the logical interconnect shown is true?
- A. For FC uplink sets, an additional uplink from second module should be added for redundancy.
- B. Additional uplink ports can be added to ETH-Uplink to increase available bandwidth.
- C. The maximum supported number of the internal networks for logical interconnect is configured.
- D. FC uplinks are not supported and will be converted to FCoE or RoCE uplinks.
Answer: D
NEW QUESTION 34
Click the option from the HPE OneView main menu that will allow you to define UPS or other components that will work as a placeholder in a rack system.
Answer:
Explanation:
NEW QUESTION 35
For HPE Primera, match each task with the management tool that can be used to perform it.
Answer:
Explanation:
NEW QUESTION 36
Refer to the exhibit.
A customer complains that firmware compliance is empty. The customer confirmed that Synergy Service Pack is uploaded to the HPE OneView repository. How should you respond?
- A. The firmware repository service must be restarted using maintenance connection.
- B. The refresh procedure must be performed on each logical enclosure to refresh firmware.
- C. The firmware repository is not defined within firmware compliance report.
- D. All of the components are up to date and compliant with firmware baseline.
Answer: A
NEW QUESTION 37
......
Verified HPE2-T37 Exam Dumps Q&As - Provide HPE2-T37 with Correct Answers: https://www.dumpsquestion.com/HPE2-T37-exam-dumps-collection.html
Pass Your HPE2-T37 Dumps Free Latest HP Practice Tests: https://drive.google.com/open?id=1kPGe2liTAlfJYSTXKk38Upe-1H3zQ_00